RIF-1-RPT-LV-24AC/1X21 - Relay Module

2903341

Preassembled relay module with Push-in connection, consisting of: relay base, power contact relay, plug-in display/interference suppression module, and retaining bracket. Contact switching type: 1 changeover contact. Input voltage: 24 V AC

Notes on operation FBS 2-6... plug-in bridge for the input side (A2) and FBS-2-8... plug-in bridge for the output side (11/21)

Product type Relay Module
Product family RIFLINE complete
Application Universal
Operating mode 100% operating factor
Mechanical service life approx. 107 cycles
Insulation characteristics
Insulation Safe isolation between input and output
Basic insulation between the changeover contacts
Insulation characteristics
Insulation Safe isolation between input and output
Basic insulation between the changeover contacts
Overvoltage category III
Pollution degree 2

Service life electrical see diagram
Maximum power dissipation for nominal condition 0.79 W
Test voltage (Winding/contact) 4 kVrms (50 Hz, 1 min., winding/contact)
Rated insulation voltage 250 V AC
Rated surge voltage 6 kV (Input/output)
4 kV (between the changeover contacts)

Coil side
Nominal input voltage UN 24 V AC
Input voltage range 19.2 V AC ... 27.6 V AC (20 °C)
Input voltage range in reference to UN see diagram
Mains frequency 50/60 Hz
Drive and function monostable
Drive (polarity) polarized
Typical input current at UN 33 mA
Typical response time 3 ms ... 12 ms
Typical release time range 3 ms ... 20 ms
Coil voltage 24 V AC
Protective circuit Varistor
Operating voltage display Yellow LED

Switching
Contact switching type 1 changeover contact
Type of switch contact Single contact
Contact material AgNi
Maximum switching voltage 250 V AC/DC
Minimum switching voltage 12 V (10 mA)
Limiting continuous current 10 A (see diagram)
Maximum inrush current 25 A (20 ms, N/O contacts)
Min. switching current 10 mA (12 V)
Interrupting rating (ohmic load) max. 240 W (24 V DC)
58 W (48 V DC)
48 W (60 V DC)
50 W (110 V DC)
80 W (220 V DC)
2500 VA (250 V AC)
Utilization category CB Scheme (IEC 60947-5-1) AC15, 1.5 A/240 V (N/O contact)
AC15, 3 A/250 V (N/C contact)
DC13, 2 A/24 V (N/C contact)
DC13, 0.2 A/250 V (N/O contact)

Connection method Push-in connection
Stripping length 8 mm
Conductor cross section rigid 0.14 mm² ... 1.5 mm²
Conductor cross section flexible 0.14 mm² ... 1.5 mm²
0.14 mm² ... 1.5 mm² (Ferrule with plastic sleeve)
0.14 mm² ... 1 mm² (Ferrule with plastic sleeve, two conductors on double terminal block)
Conductor cross section AWG 26 ... 16 (solid)
26 ... 16 (flexible)

Drill hole
Diameter 3.2 mm
Width 16 mm
Height 96 mm
Depth 75 mm

Color gray (RAL 7042)
Flammability rating according to UL 94 V2 (Housing)

Ambient conditions
Degree of protection (Relay base) IP20 (Relay base)
Degree of protection (Relay) RT III (Relay)
Ambient temperature (operation) -40 °C ... 50 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C

Corrosive gas test
Identification ISA-S71.04. G3 Harsh Group
EN 60068-2-60