FL SWITCH 1824 - Industrial Ethernet Switch

2891041

Ethernet switch, 24 Ethernet ports on the front in RJ45 format, automatic detection of 10 or 100 Mbps data transmission rate, coupling of network segments with different transmission speeds, auto crossing function, installs in 19-in. (482 mm) rack

Ethernet interface
The FL SWITCH 1824 has 24 Ethernet ports in RJ45 format. It is mounted in a 19-in. (482 mm) rack with AC power. The data transmission speed is 10 Mbps or 100 Mbps. In addition, each port has an auto crossing function at 100 Mbps: It is not necessary to make a distinction between 1:1 or crossover Ethernet cables. Mounting brackets and a German power cord are included. User supplies screws for bracket to rack connection.

Switching properties of FL SWITCH 1824
–Store-and-forward:
All data telegrams that are received by the switch are saved and their validity is checked. Invalid or faulty data packets (>1522 bytes or CRC errors) and fragments (<64 bytes) are rejected. Valid data telegrams are forwarded by the switch. The switch always forwards the data using the data transmission speed that is used in the destination network segment.
–Multi-address function:
The switch independently learns the addresses for termination devices, which are connected via a port, by evaluating the source addresses in the data telegrams. Only packets with unknown addresses, with a source address of this port or with a multicast/broadcast address in the destination address field are forwarded via the corresponding port. The switch can store up to 8192 MAC addresses in its address table.
-Quality of service (QoS): IEEE 802.1P/Q
In revision version VC03 and higher, FL SWITCH 1824 switches are capable of reading Ethernet packets that have already been assigned a priority level by a managed switch. Four priority queues are supported. The highest priority queue supports packet priorities 6 and 7, the next lowest queue supports priorities 4 and 5, the next lowest queue supports priorities 2 and 3, and the lowest priority queue supports packet priorities 0 and 1. After prioritization, the packets are forwarded without modification.

Width 440 mm
Height 44 mm
Depth 173 mm

Utilization restriction
EMC note EMC: class A product, see manufacturer's declaration in the download area

Mounting type Rack mount, includes brackets

Ethernet
Connection method RJ45
Transmission speed 10/100 Mbps
Transmission physics Twisted pair connection
Transmission length 100 m (per segment)
Signal LEDs Data receive, link status
No. of channels 24 (RJ45 ports)

Product type Switch
Product family Unmanaged Switch 1800
Type Stand-Alone
MTTF 22.9 Years (MIL-HDBK-217F standard, temperature 25°C, operating cycle 100%)
Switch functions
Basic functions Unmanaged switch / auto negotiation, complies with IEEE 802.3, store and forward switching mode
Status and diagnostic indicators LEDs: US, link and activity per port
Additional functions Autonegotiation
Security functions
Basic functions Unmanaged switch / auto negotiation, complies with IEEE 802.3, store and forward switching mode

Local diagnostics US Power present Green LED
100 Port is operating at 100 Mbps Green LED
LNK/ACT Receiving/transmitting messages Green LED
Maximum power dissipation for nominal condition 220 W
Transmission medium Copper
Supply
Supply voltage (AC) 120 V AC
220 V AC
Supply voltage range 100 V AC ... 240 V AC (50/60 Hz)
Inrush current 29 A (80 µs @ 230 V AC)
Max. current consumption 1 A (maximum)
Typical current consumption 270 mA (100 V AC)
Supply: Module electronics
Supply voltage range 100 V AC ... 240 V AC
Current consumption 1 A (maximum)

Ambient conditions
Degree of protection IP20
Ambient temperature (operation) 0 °C ... 60 °C
Ambient temperature (storage/transport) -25 °C ... 70 °C
Permissible humidity (operation) 5 % ... 95 % (non-condensing)
Air pressure (operation) 86 kPa ... 108 kPa (1500 m above sea level)

Conformance with EMC directives EN 61000-4-2 (ESD) Criterion B
EN 61000-4-3 (radiated noise immunity) Criterion A
EN 61000-4-4 (EFT burst) Criterion B
EN 61000-4-5 (surge) Criterion B
EN 61000-4-6 (line noise immunity) Criterion A
EN 61000-4-8 (electromagnetic fields) Criterion A
EN 61000-4-11
EN 61000-6-3
Noise immunity EN 61000-6-2:2005
Electromagnetic compatibility Conformance with EMC directive 2004/108/EC and for low-voltage directive 2006/95/EC
Noise emission EN 61000-6-4