IB IL 24 DO 2-2A-2MBD-PAC - Digital module

2861700

Inline, Digital output terminal, Digital outputs: 2, 24 V DC, 2 A, connection technology: 4-conductor, transmission speed in the local bus: 2 Mbps, degree of protection: IP20, including Inline connector and labeling field

Width 12.2 mm
Height 119.8 mm
Depth 71.5 mm
Note on dimensions Housing dimensions

Inline local bus
Number of interfaces 2
Connection method Inline data jumper
Transmission speed 2 Mbps

Module
ID code (dec.) 189
ID code (hex) BD
Length code (hex) C2
Length code (dec) 194
Process data channel 2 bit
Input address area 0 Byte
Output address area 2 bit
Register length 2 bit
Required parameter data 3 Byte
Required configuration data 4 Byte

Digital:
Output name Digital outputs
Connection method Spring-cage connection
Connection technology 4-conductor
Number of outputs 2
Protective circuit Overload protection, short-circuit protection of outputs
Output voltage 24 V DC (US - 1 V)
Output current max. 2 A (per channel)
max. 4 A (per device)
Maximum output current per channel 2 A
Maximum output current per module 4 A
Nominal output voltage 24 V DC
Nominal load, inductive 48 VA (1,2 H, 12 Ω)
Nominal load, lamp 48 W
Nominal load, ohmic 48 W (12 Ω)
Maximum operating frequency with ohmic nominal load max. 300 Hz (this switching frequency is limited by the number of bus devices, the structure of the bus, the software used and the control or computer system used)
Reverse voltage resistance to short pulses Reverse voltage proof
Behavior with overload Auto restart
Behavior with inductive overload Output can be destroyed
Behavior at voltage switch-off The output follows the power supply without delay

Product type I/O component
Product family Inline
Type modular
Scope of delivery including Inline connector and labeling field
No. of channels 2
Operating mode Process data mode with 2 bits
Diagnostics messages Short-circuit or overload of the digital outputs Error message in the diagnostic code (bus) and display (2 Hz) via the LED (D) on the module
Insulation characteristics
Overvoltage category II (IEC 60664-1, EN 60664-1)
Pollution degree 2 (IEC 60664-1, EN 60664-1)

Potentials: Communications power (UL)
Supply voltage 7.5 V DC (via voltage jumper)
Current draw max. 60 mA
Power consumption max. 0.45 W
Potentials: Segment circuit supply (US)
Supply voltage 24 V DC (via voltage jumper)
Supply voltage range 19.2 V DC ... 30 V DC (including all tolerances, including ripple)
Current draw max. 4 A
Electrical isolation/isolation of the voltage ranges
Test voltage: 7.5 V supply (bus logics)/24 V supply (I/O) 500 V AC, 50 Hz, 1 min.
Test voltage: 24 V supply (I/O) / functional ground 500 V AC, 50 Hz, 1 min.
Test voltage: 7.5 V supply (bus logic)/functional ground 500 V AC, 50 Hz, 1 min.

Connection technology
Connection name Inline connector
Conductor connection
Connection method Spring-cage connection
Conductor cross section rigid 0.08 mm² ... 1.5 mm²
Conductor cross section flexible 0.08 mm² ... 1.5 mm²
Conductor cross section AWG 28 ... 16
Stripping length 8 mm
Inline connector
Connection method Spring-cage connection
Conductor cross section, rigid 0.08 mm² ... 1.5 mm²
Conductor cross section, flexible 0.08 mm² ... 1.5 mm²
Conductor cross section AWG 28 ... 16
Stripping length 8 mm