MINI MCR-2-POT-UI-PT - Resistance/potiposition transducer

2902017

Configurable potiposition transducer with plug-in connection technology for connecting potentiometers from 0 Ω ... 100 Ω to 0 kΩ ... 100 kΩ. Configurable via DIP switch or software. push-in connection technology, standard configuration

Configurable, 3-way isolated potentiometer measuring transducer with plug-in connection technology. The measured values are converted into a linear and freely adjustable current or voltage signal. You can configure the device using one of the free software solutions. Default settings can also be made directly on the device by simply using the DIP switches (see configuration table). If it is not possible to fully utilize the potentiometer range, you can specify the upper and lower potentiometer values in the software. The measuring transducer supports fault monitoring and NFC communication.

Utilization restriction
EMC note EMC: class A product, see manufacturer's declaration in the download area

Product type Potiposition transducer
Product family MINI Analog Pro
No. of channels 1
Configuration DIP switches
Software
App
Insulation characteristics
Overvoltage category II
Pollution degree 2

Functionality
Configuration DIP switches
Software
App

Electrical isolation 3-way isolation
Protective circuit Transient protection
Step response (0–99%) < 60 ms
Maximum temperature coefficient 0.01 %/K
Temperature coefficient, typical 0.01 %/K
Maximum transmission error < 0.1 % (R < 240 Ω = < 0,2 %)
Electrical isolation Input/output/power supply
Rated insulation voltage 300 Vrms
Test voltage 3 kV AC (50 Hz, 60 s)
Insulation Reinforced insulation according to IEC/EN 61010-1
Supply
Nominal supply voltage 24 V DC
Supply voltage range 9.6 V DC ... 30 V DC (The DIN rail connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, item no. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail in accordance with EN 60715)
Typical current consumption 33 mA (24 V DC)
68 mA (12 V DC)
Power consumption ≤ 850 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)

Signal: Resistance
Number of inputs 1
Available input sources 3-wire potentiometer
Resistance range 0 Ω ... 100 Ω
0 Ω ... 100 kΩ

Signal: Voltage/current
Number of outputs 1
Voltage output signal 1 V ... 5 V (via DIP switch)
10 V ... 0 V (via DIP switch)
0 V ... 5 V (via DIP switch)
0 V ... 10 V (via DIP switch)
0 V ... 10.5 V (can be set via software)
Max. voltage output signal  12.3 V
Non-load voltage < 17.5 V
Current output signal 0 mA ... 20 mA (via DIP switch)
4 mA ... 20 mA (via DIP switch)
20 mA ... 0 mA (via DIP switch)
20 mA ... 4 mA (via DIP switch)
0 mA ... 21 mA (can be set via software)
Max. current output signal 24.6 mA
Short-circuit current < 31.5 mA
Load/output load voltage output ≥ 10 kΩ
Load/output load current output ≤ 600 Ω (20 mA)
Ripple < 20 mVPP
< 20 mVPP (10 kΩ)
Resolution, outputs (voltage) 1 mV
Resolution, outputs (current) 2 µA
Behavior in the event of a sensor error configurable

Connection method Push-in connection
Stripping length 10 mm
Conductor cross section rigid 0.2 mm² ... 2.5 mm² (with ferrule)
0.14 mm² ... 2.5 mm² (without ferrule)
Conductor cross section flexible 0.14 mm² ... 2.5 mm²
Conductor cross section AWG 24 ... 12 (flexible)