AXL F DI16/1 DO16/1 2H - Digital module

2702106

Axioline F, Digital I/O module, Digital inputs: 16, 24 V DC, connection technology: 1-conductor, Digital outputs: 16, 24 V DC, 500 mA, connection technology: 1-conductor, transmission speed in the local bus: 100 Mbps, degree of protection: IP20, including bus base module and Axioline F connectors

Width 35 mm
Height 129.9 mm
Depth 54 mm
Note on dimensions The depth applies when a TH 35-7.5 DIN rail is used (in accordance with EN 60715).

Axioline F local bus
Number of interfaces 2
Connection method Bus base module
Transmission speed 100 Mbps

Module
Input address area 2 Byte
Output address area 2 Byte
Required parameter data 3 Byte
Required configuration data 7 Byte

Digital:
Input name Digital inputs
Description of the input EN 61131-2 types 1 and 3
Number of inputs 16
Connection method Push-in connection
Connection technology 1-conductor
Input voltage range "0" signal -3 V DC ... 5 V DC
Input voltage range "1" signal 11 V DC ... 30 V DC
Nominal input voltage UIN 24 V DC
Nominal input current at UIN 2.4 mA
Input filter time 3000 µs (Default)
1000 µs
< 100 µs
Protective circuit Polarity reversal protection of the inputs; parallel diode (30 V, 5 s)

Digital:
Output name Digital outputs
Connection method Push-in connection
Connection technology 1-conductor
Number of outputs 16
Protective circuit Short-circuit protection, overload protection of the outputs; electronic
Output voltage 24 V DC
Limitation of the voltage induced on circuit interruption -25.8 V ... -15 V
Maximum output current per module 8 A (provide external protection)
Nominal output voltage 24 V DC
Load min. 10 kΩ
Output voltage when switched off max. 1 V
Output current when switched off max. 300 µA
Nominal load, inductive max. 12 VA (1.2 H, 48 Ω, with nominal voltage)
Nominal load, lamp max. 12 W (at nominal voltage)
Nominal load, ohmic max. 12 W (48 Ω, with nominal voltage)
Switching frequency max. 10000 per second (with at least 50 mA load current)
max. 1 per second (with inductive load)
max. 16 per second (with nominal lamp load)
Reverse voltage resistance to short pulses limited protection up to 0.5 A for 1 s
Behavior with overload Shutdown with automatic restart
Behavior with inductive overload Output can be destroyed
Signal delay max. 100 µs (when switched on)
max. 100 µs (when switched off, with at least 50 mA load current)
Overcurrent shut-down as of 0.7 A
Output current with ground connection interrupt when switched off < 1 mA

Product type I/O component
Product family Axioline F
Type block modular
Mounting position any (no temperature derating)
Scope of delivery including bus base module and Axioline F connectors
Insulation characteristics
Overvoltage category II (IEC 60664-1, EN 60664-1)
Pollution degree 2 (IEC 60664-1, EN 60664-1)

Potentials: Axioline F local bus supply (UBus)
Supply voltage 5 V DC (via bus base module)
Current draw max. 120 mA (up to HW 01)
max. 60 mA (from HW 02)
Power consumption max. 600 mW (up to HW 01)
max. 300 mW (from HW 02)
Potentials: Supply for digital input and output modules (UIO)
Supply voltage 24 V DC
Supply voltage range 19.2 V DC ... 30 V DC (including all tolerances, including ripple)
Current draw max. 8 A (provide external protection)
Power consumption max. 240 W (of which 1.25 W internal losses)
Protective circuit Surge protection; electronic (35 V, 0.5 s)
Reverse polarity protection; parallel diode; with external 5 A fuse (only for commissioning)