TC EXTENDER 2001 ETH-2S - Ethernet extenders

2702409

Second generation: Unmanaged Ethernet extender for point-to-point connections, line and ring structures, data rates up to 30 Mbps, distances of up to 20 km on in-house copper cables, diagnostics via USB and LEDs, 2 SHDSL ports, 1 LAN port

The Ethernet extender makes broadband Ethernet applications on existing cables possible. It is the successor to the first generation PSI MODEM SHDSL/ETH, Item No. 2313643. The Ethernet extender can be used for in-house 2 and 4-wire cables, but not in the public telephone network. Point-to-point, line or ring structures can be established, with ranges of up to 20 km.
You can use the Ethernet extender in a network with first generation devices (PSI-MODEM-SHDSL/ETH from firmware version 4.xx). The Ethernet extender can also be combined with managed Ethernet extenders: TC EXTENDER 6004 ETH-2S, Item No. 2702255 and TC EXTENDER 4001 ETH-1S, Item No. 2702253. This enables the central diagnosis of all users and lines via IP.

Utilization restriction
CCCex note Use in potentially explosive areas is not permitted in China.

Product type Ethernet extenders
MTTF 711 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
308 Years (SN 29500 standard, temperature 40°C, operating cycle 34.25%)
125 Years (SN 29500 standard, temperature 40°C, operating cycle 100%)

Functionality
Basic functions Ethernet extenders in accordance with ITU-T G.991.2

Electrical isolation VCC // Ethernet // DSL (A) // DSL (B) // FE
Maximum power dissipation for nominal condition 4.32 W
Mains type Permanent line
Test voltage data interface/power supply 500 V AC (In accordance with EN/IEC 60079-7)
1.5 kV AC (50 Hz, 1 min.)
Supply
Supply voltage range 18 V DC ... 30 V DC
Nominal supply voltage 24 V DC ±5 % (as an alternative or redundant, via backplane bus contact and system current supply)
5 V DC (configuration only, via mini-USB type B)
Typical current consumption < 180 mA (24 V DC)
Max. current consumption ≤ 2 A (For operation in a joining station, via the DIN rail connector)
Function
Status and diagnostic indicators LEDs: US (supply voltage), ACT/LINK (Ethernet data traffic), ERR (errors)
2x LINK / 2x STAT (DSL data traffic port A and port B), DIAG (diagnostic messages)

Signal
Output name Digital output
Number of outputs 2
Voltage output signal 18 V DC ... 30 V DC (depending on the operating voltage)
Current output signal ≤ 150 mA (Short-circuit-proof)
Behavior of outputs Deactivated for device supply via DIN rail connector

Supply
Connection method COMBICON plug-in screw terminal block
Tightening torque 0.56 Nm ... 0.79 Nm

Signal Ethernet
Basic functions Ethernet extenders in accordance with ITU-T G.991.2
Data: Ethernet interface, 10/100Base-T(X) in accordance with IEEE 802.3
Serial transmission speed 10/100 Mbps, auto negotiation
Connection method RJ45 jack, shielded
1 port 10/100Base-T(X), auto negotiation
No. of channels 1
Transmission length < 100 m (shielded twisted pair)
Protocols supported Protocol-transparent for TCP/IP, IPv4, and IPv6
Data: SHDSL interface according to ITU-T G.991.2.bis
Serial transmission speed 4-wire operation: 64 kbps ... 30 Mbps
2-wire operation: 32 kbps ... 15.3 Mbps
Connection method 2 x 2-pos. COMBICON plug-in screw terminal blocks
No. of channels 2 (2-wire operation)
Tightening torque 0.56 Nm ... 0.79 Nm
Transmission length < 20 km (Depending on data rate and cable cross section)
Single conductor/terminal point, rigid 0.2 mm² ... 2.5 mm²
Single-wire/terminal point, flexible 0.2 mm² ... 2.5 mm²
Max. AWG conductor cross section, flexible 14