Company: | 上海当临自动化科技有限公司 |
Location: | China - Shanghai,上海市青浦区练西公路2850号1幢 |
Price: | Negotiation |
Contact: | Jason(Manager) |
Contact Me: |
Tell:+86-19921425125 Mobile:+86-19921425125 Email:411153134422843109866557@10q4q127.c117om |
PLC-RPT-230UC 21-21 MS - Relay Module
PLC-RPT-230UC/21-21/MS - Relay Module
2910523
PLC-INTERFACE, consisting of a relay base and pluggable power contact relay with manual operation, integrated status LED, Push-in connection, 2 changeover contacts, Bridge rectifier, Input voltage: 230 V AC / 220 V DC
Product type Relay Module
Product family PLC-INTERFACE
Application Palm switch
Operating mode 100% operating factor
Mechanical service life 5x 106 cycles
Insulation characteristics
Insulation Safe isolation, reinforced insulation
Insulation characteristics: Standards/regulations
Insulation Safe isolation, reinforced insulation
Overvoltage category III
Pollution degree 2
Maximum power dissipation for nominal condition 1.15 W
Test voltage (Winding/contact) 4 kVrms (50 Hz, 1 min., winding/contact)
Test voltage (Changeover contact/changeover contact) 2.5 kVrms (50 Hz, 1 min., changeover contact/changeover contact)
Standards/regulations
Rated insulation voltage 250 V AC
Rated surge voltage 6 kV
Coil side
Nominal input voltage UN 230 V AC
220 V DC
Input voltage range 207 V AC ... 264.5 V AC (20 °C)
209 V DC ... 264 V DC
() 110 V DC
Drive and function monostable
Drive (polarity) polarized
Typical input current at UN 5 mA
Typical response time 6 ms (220 V DC)
3 ms ... 15 ms (230 V AC)
Typical release time 10 ms (220 V DC)
Typical release time range 3 ms ... 15 ms (230 V AC)
Protective circuit Bridge rectifier; Bridge rectifier
Operating voltage display Yellow LED
Switching
Contact switching type 2 changeover contacts
Type of switch contact Single contact
Contact material AgNi
Maximum switching voltage 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Minimum switching voltage 12 V (10 mA)
Limiting continuous current 6 A
Maximum inrush current 12 A (20 ms)
Min. switching current 10 mA (12 V)
Interrupting rating (ohmic load) max. 192 W (24 V DC)
62 W (48 V DC)
42 W (60 V DC)
55 W (110 V DC)
66 W (220 V DC)
2000 VA (250 V AC)
Switching capacity 1 A (24 V, DC13)
1.5 A (230 V, AC15)
Connection method Push-in connection
Stripping length 10 mm
Conductor cross section rigid 0.14 mm² ... 2.5 mm²
Conductor cross section flexible 0.14 mm² ... 2.5 mm²
0.2 mm² ... 2.5 mm² (Single ferrule)
2x 0.5 mm² ... 1 mm² (TWIN ferrule)
Conductor cross section AWG 26 ... 14
Width 14 mm
Height 80 mm
Depth 104 mm
Disclaimer:All information is provided by registered users. You may assess risks based on corresponding qualifications.
- CY7C68013A-56LTXC.CYPRESSIntroducing the CY7C68013A-56LTXC , the latest in cutting-edge USB technology ." "
- MAX4544EUT+T.MAXhe MAX4544EUT+ is the ultimate solution for all your audio and video signal processing needs ." "
- VNQ7040AYTR.STIntroducing the VNQ7040AYTR , the latest innovation in technology that is sure to take your experience to the next level ." "
- TMS320F28335PGFA.FZXIntroducing the TMS320F28335PGFA , the latest and most advanced microcontroller from Texas Instruments ." "